This great article below involving How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is truly motivating. You should give it a look.
Setting up a bath tub isn't exactly rocket science, yet it does call for solid plumbing, woodworking, as well as often, tiling abilities. Changing an old bathtub with a new one is likewise a reasonably tough task. If the old bathtub is conveniently accessible, the task can relocate easily; if you have to open up a wall surface to get rid of the old tub and position the brand-new bath tub, the job is much harder. In either case, the job is within a house handyman's abilities, although you will certainly require an assistant to move out the old tub and set in the new one. Make certain you have actually certified on your own for the task as well as fit trying it. As opposed to working with a contractor to take over a halfway-completed project, it is better to consider employing one before you begin. Chances are you may need a professional plumber to make tube connections.
This short article will help you install a new bathtub in your restroom if you have already bought a new tub and also do not require to transform the setup of your previous water pipelines.
Your devices as well as product checklist ought to make up the following:
Preparing for the Installment
First of all, the supporting frame supplied with the bathroom needs to be fitted (if called for) according to the maker's directions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is essential to make sure that if the faucet includes a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the taps device to avoid pressure on the bath tub.
Fit the versatile tap adapters to the bottom of both taps using 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet through the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you use every one of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom ought to currently be ready to be suited its last position.
Removing Old Touches
If you need to change old taps with new ones as a part of your installment, then the first thing you must do is disconnect the water system. After doing so, activate the taps to drain any kind of water continuing to be in the system. The process of getting rid of the existing taps can be rather bothersome as a result of the restricted gain access to that is usually the case.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the taps. Have a fabric all set for the remaining water that will originate from the pipelines. Once the supply pipes have actually been gotten rid of, make use of the same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from transforming during this process. When the faucets have actually been gotten rid of, the holes in the bath/basin will have to be cleaned up of any type of old securing substance.
Before proceeding to fit the new faucets, compare the pipeline links on the old faucets to the new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Installing the Bathtub
Utilizing the two wooden boards under its feet, place the bathtub in the needed setting. The wood boards are practical in equally spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto four small points.
The next goal is to guarantee that the bathtub is leveled all round. This can be accomplished by inspecting the spirit level as well as changing the feet on the tub up until the level checks out level.
To set up taps, fit the bottom of the furthest flexible tap connector to the suitable supply pipe by making a compression join; then do the same for the other faucet.
Activate the water and also examine all joints and also brand-new pipework for leakages as well as tighten them if required. Fill the bathtub and additionally examine the overflow electrical outlet and also the typical outlet for leaks.
Finally, fix the bathroom paneling as explained in the producer's instruction manual. Tiling and securing around the bath tub must wait up until the bathtub has been made use of at the very least when as this will settle it right into its last setting.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic port to avoid damage to the string. One end of the adapter fits on the plastic tail of the tap and the various other end supplies a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly need decreasing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, place the tap in the mounting opening in the bath/basin guaranteeing that the washers remain in location between the faucet as well as the sink. Secure the faucet in place with the supplier supplied backnut. Once the faucet is securely in position, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with regular tap adapters. The previous type must be connected to the faucet ends initially, tightening just by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bath satisfies the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is very important as the installation can relocate enough to split a rigid seal, causing the water to permeate the wall surface between the bathroom as well as the tiling, leading to difficulties with moisture and possible leaks to the ceiling below.
You can pick from a range of coloured sealants to blend in your components and also fittings. They are offered in tubes as well as cartridges, and can securing spaces as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of drenched newspaper or soft rope. Keep in mind to always fill up the bath tub with water before sealing, to permit the movement experienced when the bathtub remains in use. The sealant can break rather early if you do not take into account this movement before securing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily offered on the marketplace. It is advisable to fit the ceramic tiles making use of waterproof or waterproof sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I recently found that blog post on How to Install a Bathtub when doing a lookup on the web. Sharing is nice. Helping people is fun. I value reading our article about A Step-by-Step Guide to Installing a Bathtub.
Get Estimate